Feeder Clamp – Upon What Justification Should You Really Make A Choice..

Grounding exterior cables is equally as crucial as selecting the best cables for the television or Internet system. Grounding may prevent shocks from lightning strikes and surges from shooting across your coaxial cable and into the back of your television or Internet system. It’s also not very difficult: anyone capable of connecting 1/2” Superflex RF Coaxial Cable can ground that very same cable to an existing electrical ground with little problem.

Any television system with wires running outdoors should ground them. Attach the grounding block to your property, somewhere near in which the coaxial cable will come in. A grounding block could have a minimum of two screw holes; drill holes for each, then secure the block towards the wall with the included screws.

Disconnect the coaxial cable from the splitter and hook it up to a single side from the grounding block. This can be done just by twisting the conclusion until it will come loose. Lightly coat the ports on the grounding block with all the silicone grease. This will help in weatherproofing the ports. Perform the same for just about any open ports on the coaxial splitter.

Connect a brand new RG-6 coaxial cable to the stage on the splitter where previous cable was disconnected. Then attach one other end of the cable towards the other part from the grounding block. Coaxial cables attach by inserting the pin from the middle of the cable in to the pin-sized hole on the port, then twisting the cable until it secures in place.

Attach the grounding wire for the grounding screw on the grounding block. Loop the wire round the screw and twist the screw in until the wire is secure. Then run the wire to the electrical ground and attach the wire there in the same way. If no screw can be obtained, twist the conclusion in the cable around the ground as tightly as is possible; crimping with pliers if required.

Before I get into how and why you should ground your antenna, I wanted to let you know I am no electrician. I’m a DIY weekend warrior that relies upon Internet search-fu to learn how to do household repairs and installs.

For just about any engineers or electricians that stop by, I welcome any critiques or corrections inside the comments. Accuracy is really important in my opinion, and that i appreciate any corrections or adjustments you are able to offer.

That said, years of doing work in enterprise architecture make me somewhat of a stickler for standards and practices. Should you be too, you may want to take a look at Article 810 in the National Electric Code. It covers all the codes and standards for installing the cabling for TV and radio transmitters.

However, in case you are like most people, you’d rather hit your thumb repeatedly having a hammer than suffer through technical manuals. If so, I’ll do my advisable to take you step-by-step through what I did after looking on the code.

Below is really a picture describing just what we are going to do. It illustrates how to ground your antenna by connecting it to your house’s ground wire. Notice you must not only ground the Universal Grounding Kit, however the antenna mast as well.

Grounding an antenna isn’t challenging to accomplish yourself, however it shouldn’t be expensive to have a professional appear and do this to suit your needs. In order to attempt this, listed here are are definitely the steps I took to recreate what is essentially depicted in the diagram.

Cable installation basics. Install equipment and cabling in a neat and workmanlike manner [820.24]. You can find the industry practices described in ANSI/NECA/BICSI 568, Standard for Installing Commercial Building Telecommunications Cabling.

Exposed cables must be backed up by the structural components of the property to avoid cable damage as a result of normal building use. Secure cables with straps, staples, hangers, or similar fittings designed and fmpuqh so as to not damage the cable.

Cables run parallel to framing members or furring strips should be protected where they could be penetrated by nails or screws. To offer this protection, you might have two options. Install the cables at least 1¼ inches from your nearest side of the framing member or furring strips.

Protect the Coax Cable Clamp having a 1/16-inch-thick steel plate Wiring support rules for coaxial cables could be a little tricky. Make sure you know when and where independent support wires should be used. You need to securely fasten raceways that have coaxial cables set up. Don’t use ceiling-support wires or even the ceiling grid to aid raceways or cables. You are able to, however, support raceways and cables with independent support wires attached to the suspended ceiling.